It is currently Wed Jun 19, 2013 4:58 am

All times are UTC - 7 hours



Post new topic Reply to topic  [ 24 posts ]  Go to page Previous  1, 2, 3  Next
Author Message
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Wed Nov 02, 2011 10:38 am 
Offline

Joined: Thu Sep 01, 2011 9:41 am
Posts: 37
avatar2100 wrote:
Gibson is a solid guitar, real guitar.


Sure they are. But hell with your vast knowledge of wood the mahogany body will look like particle board to you.


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Wed Nov 02, 2011 11:53 pm 
Offline

Joined: Thu Sep 01, 2011 1:12 pm
Posts: 15
avatar2100 wrote:
Gibson is a solid guitar, real guitar.

If you're talking about their LP, a real guitar perhaps, but a neck thru, no... Therefore, the construction method is very different!
So much for your luthier knowledge BTW! :roll:


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Thu Nov 03, 2011 11:22 am 
Offline

Joined: Sun Oct 30, 2011 3:56 pm
Posts: 10
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image

Jackson RR1 made of 9 pieces, the wood is very light, neck combined from two parts, this method applies to cheap guitars.. The body is made of 7 pieces. In front and rear maple veneer is applied to mask the joints. In conclusion, is this a $2900 guitar?

http://www.jacksonguitars.com/products/ ... 2803060827


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Sun Nov 06, 2011 2:57 pm 
Offline

Joined: Sun Nov 06, 2011 2:48 pm
Posts: 4
...

I want a Randy Rhoads, and you can afford to cut one up... T.T


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Sun Nov 06, 2011 4:30 pm 
Offline

Joined: Sun Oct 30, 2011 3:56 pm
Posts: 10
A real guitar Explorer 84...

Image
Image
Image
Image


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Wed Nov 09, 2011 7:56 pm 
Offline

Joined: Sat Oct 08, 2011 7:55 pm
Posts: 4
That part where the neck is glued to the headstock is not low-quality at all. It's called a scarf joint. A scarf joint is used to connect the headstock to the neck in some guitars. Gibson necks, however, are cut from a single piece of wood. There is no scarf joint where the headstock meets the neck in a Gibson. This is one of the reasons you hear about headstock/neck breakage so often in LPs and other Gibbys. Necks cut from a single piece have "short grain" in the headstock, which translates into an intrinsically weak neck.

One of the ways around this problem is to cut a scarf joint from the same board, reverse the piece, and glue it on. The cut is made at the headstock angle, whatever it is. This gives you "long grain" in both the neck and the head stock. With a good cut and a solid glue joint these scarf joint necks are considerably stronger than the 1 piece neck construction.
http://i492.photobucket.com/albums/rr28 ... fJoint.jpg


Last edited by KadenH on Wed Nov 09, 2011 8:11 pm, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Wed Nov 09, 2011 8:09 pm 
Offline

Joined: Sat Oct 08, 2011 7:55 pm
Posts: 4
Also, the way the neck and center of the body are made from one piece of maple is better for sustain. Your '84 explorer has a glued on neck, which has less sustain and is usually cheaper.

Let me be clear:
I am not dissing your guitar in any way. '84 Explorer is one of the sexiest guitars I've ever seen :D


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Fri Nov 11, 2011 10:06 am 
Offline

Joined: Sun Oct 30, 2011 3:56 pm
Posts: 10
Image

Image

Image
Image
Image
Image
Image
Image
Image


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Fri Dec 02, 2011 3:02 pm 
Offline

Joined: Sun Oct 30, 2011 3:56 pm
Posts: 10
Image
Image
Image
Image


Top
 Profile  
 
 Post subject: Re: You thought that Jackson RR1 Made in USA is neck thru bo
PostPosted: Mon Dec 12, 2011 8:24 am 
Offline

Joined: Thu Sep 01, 2011 9:33 am
Posts: 15
Congratulations on ruining a great guitar!

what a nimrod

_________________
Kelly and Warrior 7 Strings please


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 24 posts ]  Go to page Previous  1, 2, 3  Next

All times are UTC - 7 hours


Who is online

Users browsing this forum: Google [Bot], jstarguitars and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group